Menu
- Komis, usługi(1)
- Helikoptery(1035)
- Drony(786)
- Wielowirnikowce Bind & Fly(34)
- Blade, nQX mQX Części(9)
- Ramy(125)
- Akcesoria(112)
- Regulatory(49)
- Kontrolery(120)
- Śmigła(212)
- Silniki(83)
- PDB i BEC(20)
- Elektronika(21)
- Plecaki i Torby(10)
- Samoloty(3)
- Aparatury i Odbiorniki(153)
- Żyroskopy i FBL(75)
- Elektronika(303)
- FPV(228)
- Łopaty Śmigła(302)
- Ładowarki(36)
- Akumulatory(57)
- Akcesoria(385)
- Symulatory(5)
- Nowości
- Promocje
Producenci
Promocje
Tattu R-Line V4 1300mAh 14.8V 130C 4S1P Lipo
Dron iFlight Nazgul Evoque F5D HD Vista Nebula Pro 4s
Dron iFlight Nazgul Evoque F5D Analog 4s
Dron iFlight Nazgul Evoque F5D HD Vista Nebula Pro 6s
Dron iFlight Nazgul Evoque F5X HD Vista Nebula Pro 6s
Dron iFlight Nazgul Evoque F6X Analog 6s
Dron iFlight Nazgul Evoque F6X HD Vista Nebula Pro 6s
Dron iFlight Nazgul Evoque F5X HD Vista Nebula Pro 4s
Dron iFlight Nazgul Evoque F5D Analog 6s
Dron iFlight Nazgul Evoque F6D HD Vista Nebula Pro 6s
Dron iFlight Nazgul Evoque F6D Analog 6s
Dron iFlight Chimera7 Pro 6S LR HD System
MATEK AP_Periph CAN Magnetometer RM3100
Dostępność:
dostępny
Wysyłka w:
24 godziny
Producent:
Kod produktu:
MTCANL43100
Opis
- CAN-L4-3100 is a professional grade CAN Magnetometer based on RM3100 & ArudPilot AP_Periph firmware.
- RM3100 sensor technology provides high resolution, low power consumption, large signal noise immunity, a large dynamic range, and high sampling rates. Measurements are stable over temperature and inherently free from offset drift.
Specifications
- PNI RM3100 Geomagnetic Sensor
- CAN node MCU: STM32L431xC, 256KB Flash
- Interface
- CAN, DroneCAN Protocol
- UART2, MSP output (MatekL431-Periph fw)
- UART3, for external GNSS module
- ST debug, SWCLK & SWDIO
- LED
- Blue, Fast blinking, Booting
- Blue, Slow blinking, working
- Red, 3.3V indicator
- Power supply for CAN-L4-3100 board : 4.5~5.5V @5V pad/pin
- Power consumption: 22mA
- Operating Temperatures: -40~85 °C
- Physical
- Board Size: 36mm*25mm*10mm. 6g
- 3D File CAN-L4-3100_step.zip
- Firmware
- ArduPilot AP_Periph: MatekL431-GPS or MatekL431-Periph
- Update via DroneCAN GUI Tool or Mission Planner (AP_Periph.bin)
- Update via STLink (AP_Periph_with_bl.hex)
- Parameters
- CAN_P1_DRIVER = 1 if attached to CAN bus1 port or CAN_P2_DRIVER = 1 if attached to CAN bus2 port
- COMPASS_AUTODEC = 1
Packing
- 1x CAN-L4-3100 board
- 1x JST-GH-4P to JST-GH-4P 20cm silicon wire
Tips
- CAN-L4-3100 is pre-installed with “MatekL431-GPS” firmware.
- MSP feature is disabled in “MatekL431-GPS”. If you want to use MSP feature, reflash it with “MatekL431-Periph” firmware(AP_Periph_with_bl.hex) over SWC/SWD pads via ST-LINK.
- Put magnetometer far from power lines/ESC/motors/iron based material. >=10cm
- 2 ears for mounting can be cut off if you don’t need it.
- If the CAN wires are too long, bridge the “120R” jumper.