Menu
- Komis, usługi(2)
- Drony(238)
- Samoloty(3)
- Helikoptery(996)
- Aparatury i Odbiorniki(210)
- DJI FPV System(0)
- FlySky / Turnigy(2)
- FrSky(31)
- RadioMaster(61)
- Spektrum(11)
- TBS(59)
- LRS(39)
- ELRS(26)
- Akcesoria(43)
- Elektronika(457)
- FPV(261)
- Śmigła(252)
- Łopaty(70)
- Ładowarki(25)
- Akumulatory(58)
- Plecaki i Torby(15)
- Akcesoria(320)
- Symulatory(5)
- Nowości
- Promocje
Producenci
Promocje
29,00 zł
Cena regularna:
58,00 zł
23,58 zł
Cena regularna:
47,15 zł
29,00 zł
Cena regularna:
58,00 zł
23,58 zł
Cena regularna:
47,15 zł
8,50 zł
Cena regularna:
17,00 zł
6,91 zł
Cena regularna:
13,82 zł
8,50 zł
Cena regularna:
17,00 zł
6,91 zł
Cena regularna:
13,82 zł
6,25 zł
Cena regularna:
12,50 zł
5,08 zł
Cena regularna:
10,16 zł
6,25 zł
Cena regularna:
12,50 zł
5,08 zł
Cena regularna:
10,16 zł
6,25 zł
Cena regularna:
12,50 zł
5,08 zł
Cena regularna:
10,16 zł
23,50 zł
Cena regularna:
47,00 zł
19,11 zł
Cena regularna:
38,21 zł
23,50 zł
Cena regularna:
47,00 zł
19,11 zł
Cena regularna:
38,21 zł
10,00 zł
Cena regularna:
20,00 zł
8,13 zł
Cena regularna:
16,26 zł
33,50 zł
Cena regularna:
67,00 zł
27,24 zł
Cena regularna:
54,47 zł
14,50 zł
Cena regularna:
29,00 zł
11,79 zł
Cena regularna:
23,58 zł
Matek ExpressLRS/ELRS-R24-P6 2.4GHz PWM Receiver
Opis
Target
Configurator
- configurator 1.5.x or older, DIY 2.4 GHz –> DIY 2400 RX PWMP EX
- configurator 1.6.x or newer, Generic targets used as a base 2.4 GHz –> Generic ESP8285 6xPWM 2.4Ghz RX
web-flasher https://pkendall64.github.io/elrs-web-flasher
- Generic targets used as a base –> 2.4GHz Receiver –> Generic ESP8285 6xPWM 2.4GHz RX
Specifications
- ESP8285, SX1281
- Antenna connector: IPEX MHF 1
- 6x PWM outputs
- Support 2~8S VBat voltage sense
- RF Frequency: 2.4GHz (2400~2480MHz)
- Telemetry power: 12dbm
- Receiver output protocol: PWM
- Input voltage: 4~9V DC @ “+” pad
- Voltage sense: 34V Max. @ “VBat” pad
- Power dissipation: 45mA(binding), 85mA(wifi mode)
- PCB size: 20mm x 18mm
- Weight: 2g w/ antenna
- Packing:
- 1x ELRS-R24-P6
- 1x IPEX MHF1 Antennas. 15cm
- Dupont 2.54 pins (Board is shipped unsoldered)
Firmwares
- ExpressLRS 3.0 or newer, DIY 2.4 GHz / DIY 2400 RX PWMP EX
- ExpressLRS wiki for PWM receiver, Click HERE
- Make sure Receiver and TX module both are running ExpressLRS 3.0 or newer
——————————————————-
- Receiver has ExpressLRS 3.0 preloaded with binding phrase “123456”, the Receiver will never enter binding mode if using the traditional binding procedure.
- You need to reflash it with your binding phrase OR go into WebUI to set your binding phrase.
Flashing via Wifi
- Disconnect ESC and servos from receiver first.
- Power on receiver by 5V source. Receiver’s LED(Red) will blink slow at first, and after 20s, it should blink fast indicating it’s on Wifi Hotspot Mode.
- More detailed steps, pls refer this page.
- Target:
- configurator 1.5.x or older, DIY 2.4 GHz –> DIY 2400 RX PWMP EX
- configurator 1.6.x or newer, Generic targets used as a base 2.4 GHz –> Generic ESP8285 6xPWM 2.4Ghz RX
Flashing via UART
- Disconnect ESC and servos from receiver first.
- Wire the receiver into the USB-TTL adapter, with TX on receiver connected to the Rx on the USB-TTL, and RX on receiver connected to the Tx of the USB-TTL. Wire 5V and GND of the USB-TTL to 5V and GND of the Receiver.
- Press the boot button while powering on the receiver, then release – the Red LED on receiver should now be solid.
- configurator 1.5.x or older, Select the target DIY 2.4 GHz / DIY 2400 RX PWMP EX and “UART” for Flashing Method, set your bind phrase and Firmware Options and once done, click on Build and Flash.
- configurator 1.6.x or newer, Select the target Generic targets used as a base 2.4 GHz –> Generic ESP8285 6xPWM 2.4Ghz RX and “UART” for Flashing Method, set your bind phrase and Firmware Options , Check “erase before flash” and “Force FLash “.
- If you use web-flasher https://pkendall64.github.io/elrs-web-flasher/ , select Generic targets used as a base –> 2.4GHz Receiver –> Generic ESP8285 6xPWM 2.4GHz RX, and enable “Erase flash first”.